Moonwalker Movie Free Download here. Solved: I have a WAG54G ver 1.2, 4-port eth + wireless adsl router. The latest firmware update on the support download site is Ver.1.02.1 from. You can choose between a firmware based on stable sources or one based on bleeding. Then come back and update the wiki! Main firmware download server.

Im trying to implement the bootloader that you post. Im very new in this technology (coldfire) so I have a little problems trying to understand some part of the code and I need you help, I hope you can help me with my doubts. The problems are: 1.- In the RM of the MCF52223 say: 'Prior to issuing any command, it is necessary to write the CFMCLKD register to divide the input clock to within the 150 KHz to 200 KHz range.' In your code, there isn't anything like that. So, I have to do it before call the flash_upgrade function?? 2. Patch Pes 2012 Pc Serie B E Bundesliga Top here. - I don't understand how the erase page and program page command take the direction that it should be the one in the backdoor_addr, How it happens? 3.- The function splx and memcpy.

Where is declare or what it does? 4.- The 'RAM_CODE_PAGE' what it is? It is a part of a linker file or what? Egg Money Quilts Templates For Blogger. How I declare a correct RAM_CODE_PAGE??

5.- How I should declare the 'fn' 6.- And the last one is. On the function 'flash_upgrade_end' what I should do?? I will very thankful if you can help me to solve this doubts! Thanks in advance for your time!! Sorry for my bad english. Hi all I have bought this router more than one year ago Recently power led switches to red. Just after reset it was green and than became red all the time.

I find a solution to upload new firmware during this green cycle. I set static IP to my PC.

Then I use windows tftp command to do that. Upload was OK. After reboot power led always red. And I can not communicate to the device even after reset even on 10fullduplex. Is it really brick now? What can I try? PS Power supply is OK – I even tried to use regulated power supply – device consumes 260ma.

Message Edited by buslik on 12:49 AM. Hi,Mydeviceis the wag354g with firmware 1.01.03.i enabled management on port 80, and sure enough a grc.com port scan showed 80 as open!When i attempt to accessIP:80 from my place of work, I receivethe logon prompt, and get the HTML header (aka page title), but no content loads, and i get no errors. It just stays blank and says done.I think my place of work may have some policies to restrict access, as it just seems to timeout?on a slightly different note i have a linksys wireless webcam wvc54g 1.1 firmware v5.1. I set this up on port 1024, and forward this (internal port 1024) to external port 81.

My aim is to access my camera frommy place of work. To try and get around this i am forwarding to port 81 (common port which will hopefully be allowed), and registered with the sololink ddns service. This also seems to timeout after a while. The grc.com port scan just showed ports 81 and 1024 as 'stealth'.any ideas gratefully appreciated. I have a 1 week old out-the-box WAG354G version 2.

On initial set up, I plugged it all up and connected to my XP service pack 2 PC by cable, went to the web page: 192.168.1.1 without problems and set up my internet. WI-FI was set up without any problems too. At the end of the evening I turned off my PC, and turned off the router. The next day, I was met with the nice blinking green power light on my router and no internet connection. If I re-plu in my older TalkTalk modem, I get the internet - no probs. I've DL the firmware, and the tftp installer. I've pressed the reset button for at least the requested 30 seconds, but the firmware will not upgrade.

I'm informed that no server can be detected. I'm lost now as to what I need to do to get this kit running. Any help would be fantastic. Hallo i have linksys wag354g with the latest firmware 1.01.11 i have made an account at www.ddns.org and i have already configured my linksys for ddns service.In the status field shows DDNS is updated successfully but in reality it fails to update the ip.I heard that reducing mtu size of packets helps to solve the problem. Is it true?I tried already to reduce the mtu size and sometimes it refreshed my ip but not all the times just few after many retries.Has anyone solve the problem with the ddns?Is there going to be a new firmware solving this problem? Thank you in advance any help appreciated. Hi, I'm having a little problem with the HGA7S antenna.