Our Services • • • • • Geotechnical Instrumentation & Monitoring Building and Surface Settlement marker Building settlement marker is used to monitor the vertical settlement/ movement of any structure. Building settlement marker of stainless steel male and female threaded socket are embedded/ fixed to a column/ wall. The surface settlement marker is used to monitor the vertical settlement or heaving of the ground surface.

It consist a deep ground settlement point of steel rod installed into the ground with 0.02m above the ground surface. A total station or digital level equipment is used for the monitoring of these settlement points. Crack meter Monitoring Crack meter is used to measure the movement of joints or cracks on vertical walls or slope.

Maintenance and disposal of settlement gages and settlement rods. Fabrication and Installation Settlement rods shall be installed as shown in Figure 1 at the. The building settlement marker is used to monitor the vertical settlement / movement of any structure. Bouken Jidai Katsugeki Goemon Ps2 Iso Roms on this page. These reflective markers can be monitored either using total.

The standard crack meter or tell-tale is composed of two parts with scale graduated on the surface in millimetres. The scale of one part can slide on the scale of the other part. The crack meter is to be placed firmly by epoxy with the scale of reading perpendicular to the crack line at the chosen spot. The widening or closing of the joints or cracks will cause, on plate moves relative to the other. The relationship of the cursor to the scale represents the amount of movement occurring.

Inclinometer The purpose is to evaluate the stability of slopes and embankments and determine the need and timing for corrective measures. The inclinometer casing is typically installed in a near vertical borehole that passes through suspected zones of movement into stable ground. The readout unit (Ultra-rugged Field PC running Microsoft Window TM ), the inclinometer dummy probe, cable and reel of RST inclinometer system are used to record magnitude of ground movement or displacement at each depth. Vibrating Wire Piezometer Vibrating wire piezometers allow for measurements of pore water pressure under the most adverse conditions. Software Pembagi Jaringan Wifi Tidak there.

Vibrating wire piezometers have traditionally been installed in the same manner as pneumatic piezometers or standpipe piezometers. A sand intake zone is tremied around the piezometer and then sealed with bentonite. The remainder of the hole is then filled with a bentonite cement grout.

The vibrating wire piezometers contain a high tensile steel wire a fixed anchor at one end and are attached to a diaphragm in contact with water pressure at the other end. The wire is electrically plucked, with the resonant frequency of vibration proportional to the tension in the wire. This frequency induces an alternating current in a coil which is detected by the readout unit, such as the VW2106 vibrating wire readout, and then be converted to a pressure. Vibration & Noise Monitoring A vibration monitoring programme is carried out to monitor the ground vibration during construction works. The vibration meter is used to conduct the vibration monitoring. It is a microprocessor controlled seismic recorder capable of recording 300events memory during any vibration impact due to construction or other activities. The monitor measures transverse, vertical and longitudinal ground vibration.

A calculated Peak Particle Velocity (PPV) versus the corresponding frequency and the resultant Peak Vector Sum (PVS) is presented complying with the German DIN 4150 specification. A noise monitoring is carried out to monitor the noise during construction or piling activities.

A Type 1 sound level meter dedicated to environmental noise monitoring is used to conduct the noise monitoring. This unit is equipped with an advanced data logger enabling up to 12 results logged simultaneously from three independent profiles (Peak, Max, Min, RMS results from each profile) with step down to 2ms. To start the monitoring, a preamplifier with the microphone is plug into the equipment. The computational power of its digital signal processor can perform real time statistical calculations. Strain gauges & vibrating wire load cells They are used to proof-test and measure loads in tie-backs, rock bolts, ground anchors and struts.

For strain gauge load cell monitoring, the steel surface is cleaned using wire brush to remove all scale, rust and oil. The blocks are then removed from the spacing and pressed firmly against the steel surface using spacer bar as a handle. The edges of the mounting blocks are now welded in the order.

After welding cool the mounting blocks with a water soaked rad, then slacken the set screws and slide out the spacer bar. Clean away all welding slag using a chipping hammer and wire brush. The readout unit will display directly in microstation when connection to VWSG-A Strain Guages. Thus, the change of strain between the initial reading (R0) and nay subsequent reading (R1) can be calculated by simply subtracting the initial strain from the subsequent strain. The strain gauge reading obtained can be converted to the load/force in kN latter and the total changes can be calculated by compare the current reading with the initial reading. Similar to the resistance strain gauge load cells, with vibrating wire strain gauges attached to the cylinder instead of resistance gauges. Normally three gauges are attached at equal intervals around the cylinder.